Original Research
Accepted on 15 Dec 2025
A Cable Tension Measurement Method for Transmission Lines Based on Micro-Vibration Broadband Phase Motion Magnification and Deep Learning
Frontiers in Mechanical Engineering
- 138 views
173 Publications
volumes
Original Research
Published on 12 Dec 2025
Power parameter allocation of electric vehicles by integrating optimized AFSA and system parameter classification
Frontiers in Mechanical Engineering
doi 10.3389/fmech.2025.1702693
- 421 views
Original Research
Accepted on 10 Dec 2025
Simulation-Based Parameter Optimization and Experimental Assessment of Single-and Multi-Dimple Textures in Full-Film Lubrication
Frontiers in Mechanical Engineering
- 157 views
Review
Published on 10 Dec 2025
MEMS sensors and biomechanical integration for the dynamic control of prosthetic hands: a scoping review
Frontiers in Mechanical Engineering
doi 10.3389/fmech.2025.1736935
- 546 views
Correction
Published on 10 Dec 2025
Correction: Designing an E-smart manufacturing readiness assessment tool for small and medium automotive businesses
Frontiers in Mechanical Engineering
doi 10.3389/fmech.2025.1731677
- 436 views
Original Research
Published on 10 Dec 2025
Investigating the impact of imperfections around a wellbore on liner deformation during hydraulic fracturing
Frontiers in Mechanical Engineering
doi 10.3389/fmech.2025.1697890
- 480 views
Original Research
Accepted on 09 Dec 2025
Research on Fault Diagnosis in the Operation Monitoring of Permanent Magnet Synchronous Motors Through Deep Learning
Frontiers in Mechanical Engineering
- 166 views
Original Research
Published on 09 Dec 2025
Automatic detection system for aircraft engine turbine blade faults based on improved PSO
Frontiers in Mechanical Engineering
doi 10.3389/fmech.2025.1707105
- 802 views
Original Research
Published on 09 Dec 2025
Mechanical and material heterogeneity, strain localization and deformation rate effects in crushable expanded polystyrene foams
Frontiers in Mechanical Engineering
doi 10.3389/fmech.2025.1718011
- 589 views
Original Research
Accepted on 08 Dec 2025
Design of Constant Force Polishing Device for Castings Based on Kinematic Analysis
Frontiers in Mechanical Engineering
- 109 views
Original Research
Published on 08 Dec 2025
An information processing theory framework for intelligent fault diagnosis and predictive maintenance
Frontiers in Mechanical Engineering
doi 10.3389/fmech.2025.1724801
- 514 views
Original Research
Accepted on 05 Dec 2025
Fluid Flow and Mass Transport along a Microchannel with Physics-Informed Neural Networks
Frontiers in Mechanical Engineering
- 227 views
Original Research
Accepted on 04 Dec 2025
Mechanical Processing Production Management Technology Based on Event Scheduling and Digital Management System
Frontiers in Mechanical Engineering
- 152 views
Original Research
Accepted on 04 Dec 2025
Enhancing Risk-Based Engineering Design: A Hybrid Fuzzy Failure Analysis with Empirical Validation
Frontiers in Mechanical Engineering
- 138 views
Original Research
Accepted on 04 Dec 2025
Multi-objective Optimization of a Multiphase Pump Booster Unit for Enhanced Hydraulic Performance
Frontiers in Mechanical Engineering
- 110 views
Original Research
Published on 04 Dec 2025
Inertially-enhanced damping energy sink for synergistic vibration-lightweight optimization in half-car suspensions
Frontiers in Mechanical Engineering
doi 10.3389/fmech.2025.1729318
- 543 views
Original Research
Published on 03 Dec 2025
Numerical investigation of Pelton bucket geometries for performance improvement
Frontiers in Mechanical Engineering
doi 10.3389/fmech.2025.1711624
- 786 views
Original Research
Published on 03 Dec 2025
Improved design of passive wireless sensor for ultra-high temperature environment and its back-end circuit measurement system
Frontiers in Mechanical Engineering
doi 10.3389/fmech.2025.1708131
- 485 views
Original Research
Published on 03 Dec 2025
HAVEN: a hazard avoidance and VEhicular navigation system for autonomous maneuvering in the AREE venus rover
Frontiers in Mechanical Engineering
doi 10.3389/fmech.2025.1707818
- 548 views
Original Research
Published on 03 Dec 2025
Study on robotic projectile launching based on multi-factor analysis and parameter optimization
Frontiers in Mechanical Engineering
doi 10.3389/fmech.2025.1707301
- 439 views
Review
Published on 03 Dec 2025
Local mechanical characterization of cardiovascular tissues: methods, challenges, and pathways to clinical use
Frontiers in Mechanical Engineering
doi 10.3389/fmech.2025.1703081
- 785 views
Systematic Review
Published on 02 Dec 2025
A systematic review of thermodynamic modeling and machine learning integration for optimizing plate heat exchanger performance in Uganda’s brewing industry
Frontiers in Mechanical Engineering
doi 10.3389/fmech.2025.1696957
- 615 views
Original Research
Published on 02 Dec 2025
Optimization and analysis of permanent magnet assisted reluctance generator with interior rare - Earth - Less combined magnetic poles for extended range electric vehicles
Frontiers in Mechanical Engineering
doi 10.3389/fmech.2025.1723780
- 396 views
Original Research
Published on 02 Dec 2025
Optimization design and experiment of Chinese cabbage (Brassica rapa pekinensis) groove-spoon type precision seed metering device based on discrete element method
Frontiers in Mechanical Engineering
doi 10.3389/fmech.2025.1704283
- 538 views